12 GA Shotgun Cleaning Kit with Cable

Fig.1 (M0 Hero main) — Alt: 12 gauge shotgun cleaning kit with 39-inch pull-through cable, bore brush, mop, bit set and patches in olive green case

Alt：`Portable 12 gauge shotgun cleaning kit in olive green case with clear lid, hanging loop and sliding latch`

Fig.3 (M0 Hero secondary) — Alt: Portable 12 gauge shotgun cleaning kit in olive green case with clear lid, hanging loop and sliding latch

Double-Ended Nylon Brush for Chamber, Rails and Tight Corners

Alt：`12 gauge shotgun cleaning kit case interior with pull-through cable, double-ended brush, bore brush, mop and bit set`

Fig.2 (M1) — Alt: 12 gauge shotgun cleaning kit case interior with pull-through cable, double-ended brush, bore brush, mop and bit set

Action and exterior, covered.

The double-ended nylon brush scrubs the action, the choke threads, and the exterior surfaces — the areas a barrel brush never reaches. Nylon bristles keep the work non-abrasive on bluing and finish.

39-Inch Pull-Through Cable for Full-Length Barrels

Alt：`Pull-through cable with black T-handle, brass-threaded cable end, bore brush and cotton mop, 12 gauge shotgun kit`

Fig.6 (M2) — Alt: Pull-through cable with black T-handle, brass-threaded cable end, bore brush and cotton mop, 12 gauge shotgun kit

Full barrel reach, no rod.

At 39 inches the pull-through cable runs the whole length of a 12 Gauge barrel, chamber to muzzle — it fits barrels up to about 32 inches, including the 39-inch overall with handle margin. One or two passes clears fouling and moisture after the brushing is done.

12 Gauge Bore Brush and Mop for Barrel and Chamber

Alt：`Cotton mop and copper bore brush close-up with 12 gauge stamped on metal bases, shotgun cleaning kit`

Fig.5 (M3) — Alt: Cotton mop and copper bore brush close-up with 12 gauge stamped on metal bases, shotgun cleaning kit

The bore pair, stamped for the gauge.

The 12 GA copper-wire bore brush scrubs powder fouling and plastic wad residue out of the barrel, and the 12 GA cotton mop follows for a finishing pass. Both are stamped "12", so they are easy to pick out at a glance.

6-Piece Screwdriver Set and Brass Adapter for Full Maintenance

Alt：`Screwdriver bit set with Phillips and Torx bits, plastic patch holder, brass adapters, 12 gauge shotgun cleaning kit`

Fig.4 detail (M4) — Alt: Screwdriver bit set with Phillips and Torx bits, plastic patch holder, brass adapters, 12 gauge shotgun cleaning kit

Six bits, a puller, and two brass links.

The 6-piece screwdriver set (PH1, PH2, 4, 7, T15, T20) covers the screws on a shotgun with the brass connector for the handle; the plastic patch puller seats the patches for a bore-cleaner pass; and the brass adapter (8-32 to 5/16-26) bridges the two common thread patterns.

What's in the Box (39 Pieces)

Alt：`Complete 12 gauge shotgun cleaning kit: double-ended brush, bore brush, mop, patch holder, bit set, cable and patches`

Fig.4 full (M5) — Alt: Complete 12 gauge shotgun cleaning kit: double-ended brush, bore brush, mop, patch holder, bit set, cable and patches

Every one of the 39 pieces in the Shotgun Cleaning Kit for 12GA is listed below:

• 1 × Bore Brush — 12 GA (copper wire)

• 1 × Cotton Mop — 12 GA

• 1 × Double-Ended Cleaning Nylon Brush

• 1 × Black Handle

• 1 × 39 in (99 cm) Pull-Through Cleaning Cable

• 1 × Screwdriver Set — 6 pcs (PH1, PH2, 4, 7, T15, T20)

• 1 × Plastic Patch Puller — 12 GA

• 1 × Brass Adapter — 8-32 to 5/16-26

• 1 × Brass Connector — for the screwdriver handle

• 25 × Cleaning Patches — 1.5 × 3 in

Specifications

How to Use the Pull-Through Cable

After the last clay: run the 12 GA bore brush with a bore cleaner through the barrel, follow with the 12 GA cotton mop, then pull the 39-inch cable through once to clear the bore.

Bench day: the double-ended nylon brush takes the action and choke threads while the screwdriver set works the hardware; seat a patch on the puller for a bore-cleaner pass, finish with a dry patch.

Match day: the same routine between relays — brush, mop, cable, patch — and the kit goes back in the bag.

Always confirm the firearm is unloaded and follow your owner's manual before cleaning.

About the Brand

One factory, two decades of brushes.

Every brush in this kit is produced at our own Ningbo factory — est. 2004, 8 acres, up to 600,000 brushes a month — with production history for Remington®, Cabela's®, Bulldog®, and Birchwood Casey® going back to 2000. The Shotgun Cleaning Kit for 12GA carries the Huntimes name, our own brand, and the same plant ships to the United States, the European Union, and Australia.

FAQ

Q1. Which shotguns does this kit fit?

A1. The kit is built for 12 Gauge shotguns — the most common shotgun gauge in the US, from home-defense pump guns to hunting and clay guns. The bore brush, cotton mop, and plastic patch puller are all sized for 12 GA barrels, and the 39-inch cable reaches the full length of a shotgun barrel. If your shotgun is a different gauge, or you are unsure which size fits, measure the barrel or send us your model before ordering — we will confirm compatibility.

Q2. How do I use the bore brush, the mop, and the patch puller?

A2. Run the 12 GA bore brush with a bore cleaner through the barrel to scrub fouling, follow with the 12 GA cotton mop for a finishing pass, then seat a patch in the plastic patch puller to apply a bore cleaner or lift residue. Unload the firearm first, follow the owner's manual, and use a bore cleaner before brushing.

Q3. What are the screwdriver bits for?

A3. Six bits cover common shotgun hardware: PH1 and PH2 Phillips bits for trigger-guard and stock screws, slotted 4 and 7 for sight and bead screws, and T15 and T20 Torx bits for optic-mount and accessory fasteners. The brass connector for the screwdriver handle is included. Use the matching bit by hand — these are maintenance tools.

Q4. How do I use the 39-inch cable?

A4. Pull it through the barrel from chamber to muzzle — or muzzle to chamber, per your firearm manual — once or twice to clear fouling and moisture after brushing. At 39 inches it reaches the full length of a 12 Gauge barrel (fits barrels up to about 32 inches, including the 39-inch overall with handle margin). Unload the firearm first and follow the owner's manual.

Q5. Do you offer wholesale, OEM, or private-label orders?

A5. Yes. Our Ningbo factory (est. 2004; 8 acres; up to 600,000 brushes a month) has made cleaning tools for established US brands since 2000. Private label, custom kit contents, and custom packaging are available — send your quantity and specs for a quotation.

Q6. How is the kit packaged, and what are wholesale terms?

A6. Each kit ships as a complete 39-piece set, every component accounted for. Wholesale orders can be packed in retail-ready boxes, display cartons, or bulk master cartons. MOQ and lead time depend on order size and customization — ask our sales team; we ship to the US, EU, and Australia.